RIVAGE PM Firmware V4.22 (Previous version)

RIVAGE PM Firmware / Editor / StageMix Compatibility

Please make sure that all firmware versions match for CS-R10, CS-R10-S, CSD-R7, CS-R5, CS-R3, DSP-R10, DSP-RX, DSP-RX-EX, RPio622, RPio222, RIVAGE PM Editor, RIVAGE PM StageMix, and MonitorMix when you operate the RIVAGE PM system. Using an unsupported Editor/firmware combination may result in unexpected behavior.

For TWINLANe network cards to be updated simultaneously with their host device (HY256-TL, HY256-TL-SMF), install them into a corresponding slot. If any additional cards are installed after performing the update, please execute the update program again.
To update a Dante card (HY144-D, HY144-D-SRC), use the Dante Firmware Update Manager.

RIVAGE PM/CL/QL/R/Tio Compatibility

Dante I/O Supported device information

Important Notices

V4.20 is no longer available for download, because it cannot support a modified production process for CS-R5. Please use V4.21 or later instead.

Changes in V4.21

  • Adds support for a modified production process for CS-R5. It doesn’t provide any new features.

New features in V4.20

  • Now supports the WSG-HY128 HY interface card provided by Waves.

New features in V4.12

  • Now supports CS-R3 control surface.
  • Now supports DSP "Parameter Mirror" mode which synchronizes parameters between two DSP engines for systems that do not use TWINLANe.

NOTE

  • Switching the active DSP engine state while running parameter mirroring causes a very short interruption to sound output from an attached control surface.
  • SURFACE SETTINGS banks can now be assigned to USER DEFINED keys.
  • Added the ON button on the INSERT screen.
  • For details, refer to the RIVAGE PM series operation manual.

New features in V4.02

  • Now supports the CS-R5 control surface and the DSP-RX(-EX) DSP engines.
  • RIVAGE PM7 system Input channel count increased from 120 to 144 and Matrix channel count increased from 24 to 36.
  • Added the new Reverb Plug-in “Eventide SP2016”.
  • Added support for remote control from “MonitorMix” app (V1.3 or later) for iOS or Android.
  • Added improved flexibility of HY slots -
    • HY144-D, HY144-D-SRC and HY128-MD cards can now be used in any HY slot of all DSP engines (including CSD-R7)
    • Up to 48 Dante devices can now be mounted and controlled from a DSP Engine hosting two or more HY cards featuring Dante.

NOTE

When using two or more HY144-D/HY144-D-SRC cards in the same DSP engine, it is recommended to connect them both to the same Dante network. To remotely control HA of devices in different Dante networks via multiple HY-Dante cards, specify a unique subnet (network address) to each Dante network.

Make sure that all Dante Control IDs of HY144-D/HY144-D-SRC cards (including those inserted in the same DSP engine), and CL/QL series CONSOLE IDs that are connected to the same network, are unique (or switched OFF).

  • Improved operability -
    • Expanded custom fader bank capacity to 5 banks (which allows 30 custom layers per fader bay).
    • EQ screen frequency response graph view can now be visually expanded and multi-touch operation can be used (Only applies to CS-R5 and CS-R3).
    • In the SELECTED CHANNEL VIEW screen, EQ, DYNAMICS, and SEND parameters can now be controlled by the 12 encoders below the screen.
    • The order of DYNAMICS parameters has been improved, so OUTGAIN, ATTACK and RELEASE are found in logical positions, for example.
    • You can now move to the EDIT screen for the corresponding function by pressing an encoder in the Selected Channel section of the panel.
    • Added AUTO A.G./D.G. Function to channel strip encoders.
    • It is now possible to switch SEND blocks on the Overview screen and the SEND FROM/TO screen.
    • In addition, the screen layout has been updated.
  • Improved visibility
    • Expanded the meter area and increased resolution.
    • Expanded the channel name area.
  • Improved maintenance features
    • Expanded the LOG function.
    • The status of the entire system can now be monitored using the SYSTEM CONFIG screen.
  • Inserts via the TWINLANe network are now available for all channels.
  • Bay Link operation has been improved with more options in the SURFACE SETTINGS Preferences menu.
  • The file name extension for all console files has been changed to ".RIVAGEPM".
  • In Surround Mode, the option USE PHONES B FOR SURROUND MONITOR has been added.
  • Rupert Neve Designs RMP-D8, Focusrite Rednet 4/MP8R, and Yamaha Tio1608-D devices can now be remote controlled via the Dante network.
  • Added support for L-ACOUSTICS "L-ISA" desk link function.

For details, refer to the RIVAGE PM series operation manual.

Version 4 or newer for DSP-R10 contains software produced by a third party.

For information about the license, refer to *** (product name)_OSSLicense_e.pdf, which is included in the downloaded file.

Fixed Bugs in V4.22

  • Fixed a problem with V4.02 or later firmware, in which a combination of specific operations would cause the LCD touch screen(s) to become inoperable and display the following error message “Software exception has been detected. PLEASE RESTART THIS CONSOLE AS SOON AS POSSIBLE.”.

Fixed Bugs in V4.21

  • Fixed the problem in which audio input to MY-SLOT 1 of CS-R5 and CS-R3 was 1.3dB higher in level than MY-SLOT 2.

Fixed Bugs in V4.20

  • Solved a problem in which, with V4.02 and V4.12 of DSP-RX(-EX) and CSD-R7, the device may need to be restarted if control of L-ACOUSTICS Immersive Sound System “L-ISA” was enabled.

Fixed Bugs in V4.12

  • Solved some minor errors.

Fixed Bugs in V4.02

  • Solved a problem in which the current event number in the event list may not be retained when the power was turned on for RIVAGE PM10/PM7.

Limitations

If the timecode is restarted with a valid TIME CODE SOURCE selected, the timecode value will be reset to 0 after the restart, and the event list will return to the beginning.

  • Solved a problem that channel colors were not correctly displayed when recalling a scene with changed channel colors.
  • Solved a problem in which the wrong scene title and number may be displayed in the SCENE MEMORY LCD after the [INC] key or [DEC] key was rapidly pressed multiple times.
  • Solved the problem in which, after exiting the Preview mode, a different scene number would flash in the SCENE field and the SCENE field would not show the current scene number.
  • Solved the problem in which Dante I/O devices that were mounted by selecting from -ONLINE- DEVICE LIST may not become connected but be indicated as "Virtual."
  • Solved the problem in which all the port names could not be obtained for a Dante device with 33 or more inputs/outputs that was mounted to HY144-D/HY144-D-SRC.
  • Solved some other minor errors.

Known Issues

  • If an INPUT CHANNEL without ANALOG GAIN is copied using the CH COPY function, settings for ANALOG GAIN including Phantom Power and so on will unexpectedly be pasted to the destination channel(s).
  • With V4.02, V4.12, and V4.20 of DSP-RX, and CSD-R7, in rare cases, the input level meter moves on the pop-up screen for editing some plug-ins, even when audio is not input.
  • When DSP MIRROR MODE1: TWINLANe MIRROR is used, and HY card slot 2 of RPio is set to ROUTING MODE2, output patches of HY card slot 2 are not taken over automatically by a changeover from A (active DSP) to B (standby DSP).

The workaround is the following.

  • Manually Switch the unit B to the active state.
  • Set the same patch to unit B.
  • Switch unit A back to the active state.
  • MIDI NOTE ON/OFF may not be transmitted correctly if the MIDI Note ON is assigned to a User Defined Key and is rapidly pressed several times.

Notices in version updating

  • When updating CS-R5 from V4.00, first update to V4.02 and then update to V4.20. If CS-R5 is updated directly to V4.20, the touch panels will not respond when the update is completed. If this happens, skip the proper shutdown procedure and turn the power switches off and back on again. The console will operate normally once correctly updated to the V4.20.
  • When updating CS-R5 or DSP-RX(-EX) from V4.00 or V4.02, the progress bar may stop or an error may prevent the updating process. If this continues for ten minutes or longer, turn the power off and on again, then re-start the firmware update.
  • It is not possible to update DSP-RX(-EX) when using DSP Mirroring and the engine is in ‘Standby’ state. Please set DSP-RX(-EX) to ‘Active’ state and then proceed with the update.
  • The project file saving method has been changed from V1.20.
    When loading a project file saved by V1.16 or earlier, the patching of plug-ins may be unintentionally removed. If this happens, manually patch them again.
  • When updating the console’s firmware from V1.20 or earlier, the progress bar may stop at the 14/18 status, or an error may stop the updating process. If this continues for five minutes or longer, turn the power of the console to off and on, and then retry the firmware update.
  • When loading a project file saved by V1.21 and earlier, the RACK Focus status indicator on the SCENE screen may not light even if effect plug-ins or GEQs are the target of Focus Recall. To indicate the Focus status properly, open the SCENE SETUP (FOCUS) pop-up screen once, and then close it. After doing this, save the revised project file to remove this problem in the future.

Notices in version downgrading

  • Do not load a project file saved by V1.51 and later to a system running V1.21 and earlier. When loading, all plug-ins will be un-mounted in all Scenes including the current memory. In this case, re-mounting and setting up of parameters will be required.
  • When downgrading the firmware, be sure to initialize all systems after downgrading.
  • When loading data including the MixToInput settings of the V3.00 system, the MixToInput function will work in RIVAGE PM systems even of less than V3.00. However, be careful of the possibility of unwanted signal loops, etc.

Notices for usage

  • An error dialog “Console Network ring connection open! Check cable connection.” may rarely be displayed when the sampling rate is changed on the WORD CLOCK screen. However, it does not affect the actual operation.
  • When INPUT patching is performed with the maximum number of channels of the HY256-TL or HY256-TL-SMF card exceeding 256, it appears to be correctly patched but no patch is established and no audio is input.
  • No tally signal is output from a fader moved by MIDI control change.
  • In rare cases, a “DSP Disconnected!” message could be shown. If the message appears, take the following course of action:
    1. Re-Sync manually. Check this first for the fastest possible recovery (Doesn’t apply to RIVAGE PM7).
    2. If that doesn’t solve the problem, use the [RESET] button on the back of the console (Operations 1 and 2 do not mute the audio).
    3. If that doesn’t solve the problem, restart the console.
    4. If that doesn’t solve the problem, restart the DSP Engine (Doesn’t apply to RIVAGE PM7) (Operations 3 and 4 mute the audio).
  • If you recall a Scene in which a very high HA gain was set, from a scene having a low HA gain, even if no signal is patched, a very loud pink noise signal is occasionally output for a few seconds.
  • When a certain type of USB keyboard is connected to the console, the following message may appear:
    You must restart your computer to apply these changes [Restart Now] [Restart Later]
    If this message is shown, remove this USB keyboard. It is not compatible with the console and cannot be used. The console does not need to be restarted.
  • When a DSP mirroring failover occurs, if the DSP engine B is set to active, the Word Clock master will not change automatically. To prevent audio dropouts, do not turn off the power of the DSP engine A even after a failover occurs.
  • The channel name LCD cannot display unsupported characters such as Japanese kanji used in the Dante channel labels.
  • If a DSP engine hosts one or more Dante cards (HY144-D and HY144-D-SRC in Synchronous (144io Sync SRC) mode), only check the “Enable Sync to External” option for the card that operates as the master on the Dante network.

ATENŢIE

CITIȚI CU ATENȚIE ACEST ACORD DE LICENȚĂ PENTRU SOFTWARE ("AGREEMENT") ÎNAINTE DE A UTILIZA ACEST SOFTWARE. VĂ ESTE PERMIS DOAR SĂ UTILIZAȚI ACEST PRODUS SOFTWARE ÎN CONFORMITATE CU TERMENII ȘI CONDIȚIILE ACESTUI ACORD. ACEST ACORD SE ÎNCHEIE ÎNTRE DVS. (CA ENTITATE INDIVIDUALĂ SAU LEGALĂ) ȘI YAMAHA CORPORATION ("YAMAHA").

PRIN DESCĂRCAREA SAU INSTALAREA ACESTUI SOFTWARE SAU PRINTR-UN ALT MOD ÎN SCOPUL UTILIZĂRII PERSONALE, SUNTEȚI DE ACORD CU TERMENII ACESTEI LICENȚE. DACĂ NU SUNTEȚI DE ACORD CU TERMENII, NU DESCĂRCĂȚI, INSTALAȚI, COPIAȚI SAU SĂ UTILIZAȚI ALTFEL ACEST SOFTWARE. DACĂ AȚI DESCĂRCAT SAU INSTALAT SOFTWARE-UL ȘI NU SUNTEȚI DE ACORD CU TERMENII, ȘTERGEȚI IMEDIAT SOFTWARE-UL.

ACORDAREA LICENȚEI ȘI A DREPTURILOR DE AUTOR

Yamaha vă acordă astfel dreptul de a utiliza programele și fișierele de date care compun software-ul care însoțește acest Acord și toate programele și fișierele pentru modernizarea unui astfel de software care vi se poate distribui în viitor cu termenii și condițiile atașate (colectiv "SOFTWARE"), numai pe un computer, un instrument muzical sau un echipament pe care îl dețineți sau îl gestionați. Deși dreptul de proprietate asupra mediului de stocare în care este stocat SOFTWARE-ul rămâne în obligativitatea dvs., SOFTWARE-ul propriu-zis este deținut de licențiatorii Yamaha și/sau Yamaha și este protejat de legile în vigoare privind drepturile de autor și de toate prevederile aplicabile tratatului.

RESTRICȚII

  • Este posibil să nu aveți competență în inginerie, dezasamblare, decompilare sau orice altceva ce derivă dintr-o formă de cod sursă a SOFTWARE-ului prin orice tip de metodă.
  • Nu puteți reproduce, modifica, schimba, închiria, transmite prin leasing sau distribui SOFTWARE-ul integral sau parțial sau crea lucrări derivate ale SOFTWARE-ului.
  • Nu este permis să transmiteți SOFTWARE-ul electronic de la un computer la altul sau să partajați SOFTWARE-ul într-o rețea cu alte computere
  • Nu este permis să utilizați SOFTWARE-ul pentru a distribui date sau date ilegale care încalcă politica publică.
  • Nu este permis să inițiați servicii bazate pe utilizarea SOFTWARE-ului fără permisiunea companiei Yamaha Corporation.

Datele protejate prin drepturi de autor, incluzând dar fără a se limita la datele MIDI pentru cântece, obținute prin SOFTWARE, se supun următoarelor restricții pe care trebuie să le respectați.

  • Datele primite prin intermediul SOFTWARE-ului nu pot fi utilizate în scopuri comerciale fără permisiunea proprietarului drepturilor de autor.
  • Datele primite prin SOFTWARE nu pot fi duplicate, transferate sau distribuite sau redate sau difuzate pentru ascultători în public, fără permisiunea proprietarului drepturilor de autor.
  • Criptarea datelor primite prin SOFTWARE nu poate fi eliminată și nici filigranul electronic nu poate fi modificat fără permisiunea proprietarului drepturilor de autor.

REZILIEREA

Dacă o lege privind drepturile de autor sau prevederile prezentului Acord sunt încălcate, Acordul se va încheia în mod automat și imediat fără notificare din partea Yamaha. În urma unei astfel de încetări, trebuie să distrugeți imediat SOFTWARE-ul licențiat, orice documente însoțitoare scrise și toate copiile acestuia.

DESCĂRCARE SOFTWARE

Dacă credeți că procesul de descărcare a fost defectuos, puteți contacta Yamaha, iar Yamaha vă va permite să descărcați din nou SOFTWARE-ul, cu condiția să distrugeți primele copiile sau copiile parțiale ale SOFTWARE-ului obținute prin încercarea de descărcare anterioară. Această permisiune de a descărca din nou nu trebuie să limiteze în niciun fel renunțarea la garanție din Secțiunea 5 de mai jos.

DECLINAREA GARANȚIEI SOFTWARE-ULUI

Recunoașteți în mod expres și sunteți de acord că folosirea SOFTWARE-ului este pe riscul dumneavoastră.. SOFTWARE-ul și documentația aferentă sunt furnizate "CA ATARE" și fără garanții de orice fel. FĂRĂ A SE ADRESA PRIN ORICE ALT TIP DE PROVIZIOANE ALE ACESTUI ACORD, YAMAHA DECLINĂ ÎN MOD EXPRES ORICE GARANȚII PRIVIND SOFTWARE-ULUI, EXPRES ȘI IMPLICIT, INCLUZÂND, DAR FĂRĂ A SE LIMITA LA GARANȚIILE IMPLICITE DE VANDABILITATE, ADECVARE PENTRU UN ANUMIT SCOP ȘI NEÎNCĂLCAREA DREPTURILOR TERȚE. ÎN MOD SPECIFIC, DAR FĂRĂ A SE LIMITA, YAMAHA NU GARANTEAZĂ CĂ SOFTWARE-UL VA RĂSPUNDE CERINȚELOR DUMNEAVOASTRĂ, CĂ FUNCȚIONAREA SOFTWARE-ULUI VA FI NEÎNTRERUPTĂ SAU FĂRĂ EROARE, SAU CĂ DEFECȚIUNILE DIN SOFTWARE VOR FI CORECTATE.

LIMITAREA RĂSPUNDERII

OBLIGAȚIA GENERALĂ A YAMAHA ESTE DE A PERMITE UTILIZAREA SOFTWARE-ULUI ÎN CONFORMITATE CU TERMENII STIPULAȚI. ÎN NICI UN CAZ, YAMAHA NU VA FI RESPONSABILĂ PENTRU DVS. SAU ORICE ALTĂ PERSOANĂ PENTRU ORICE DAUNE, INCLUZÂND, FĂRĂ LIMITARE, DAUNE DIRECTE, INDIRECTE, ACCIDENTALE SAU CONSECUTIVE, CHELTUIELI, PIERDERI, PIERDERI DE DATELE SAU ALTE DAUNE PROVENITE DIN UTILIZARE, INCAPACITATEA DE A UTILIZA SOFTWARE-UL, CHIAR DACĂ YAMAHA SAU UN DISTRIBUITOR AUTORIZAT A FOST INFORMAT DE POSIBILITATEA UNOR ASTFEL DE DAUNE. În niciun caz, răspunderea totală a Yamaha față de dvs. pentru toate daunele, pierderile și cauzele acțiunii (indiferent dacă este contractuală, delictuală sau de altă natură) ce depășesc suma plătită pentru SOFTWARE.

SOFTWARE TERȚI

Software-ul și datele părților terțe ("SOFTWARE TERȚI") pot fi atașate la SOFTWARE. În cazul în care, în materialele scrise sau pe datele electronice care însoțesc Software-ul, Yamaha identifică orice software și date ca SOFTWARE TERȚI, recunoașteți și sunteți de acord că trebuie să respectați prevederile oricărui acord furnizat împreună cu SOFTWARE-UL TERȚI și că partea SOFTWARE-UL TERȚI este responsabilă de orice garanție sau răspundere legată de sau provenind din SOFTWARE-UL TERȚI. Yamaha nu este răspunzătoare în niciun fel pentru SOFTWARE-UL TERȚI sau pentru utilizarea de către dvs.

  • Yamaha nu oferă garanții exprese cu privire la SOFTWARE-UL TERȚI. ÎN PLUS, Yamaha DECLINĂ ÎN MOD EXPRES ORICE GARANȚIE IMEDIATĂ, INCLUSIV, DAR FĂRĂ A SE LIMITA LA GARANȚIILE IMEDIATE DE COMERCIALIZARE ȘI DE ADECVARE PENTRU UN ANUMIT SCOP, ÎN CEEA CE PRIVEȘTE SOFTWARE-UL TERȚI.
  • Yamaha nu vă va furniza niciun service sau serviciu de întreținere cu privire la SOFTWARE-UL TERȚI.
  • Yamaha nu este răspunzătoare în fața dvs. sau a oricărei alte persoane pentru orice daune, inclusiv, fără limitare, daune directe, indirecte, incidentale sau consecutive, cheltuieli, profituri pierdute, date pierdute sau alte daune rezultate din utilizare, utilizarea incorectă sau incapacitatea de a folosi SOFTWARE-UL TERȚI.

NOTIFICAREA DREPTURILOR RESTRICȚIONATE DE GUVERNUL SUA:

Software-ul este un "element comercial", deoarece acest termen este definit la 48 C.F.R. 2.101 (octombrie 1995), constând în "software de calculator comercial" și "documentație comercială de software de calculator", astfel sunt utilizați acești termeni în 48 C.F.R. 12.212 (septembrie 1995). În concordanță cu 48 C.F.R. 12.212 și 48 C.F.R. 227.7202-1 până la 227.72024 (iunie 1995), toți utilizatorii finali din S.U.A. vor achiziționa Software-ul numai cu acele drepturi enunțate în prezentul document.

GENERAL

Prezentul acord va fi interpretat în conformitate cu legea japoneză și va fi guvernat de aceasta fără a se face referire la principiile conflictului între legi. Orice litigiu sau procedură vor fi audiate în fața instanței din Tokyo, Japonia. Dacă, din orice motiv, o instanță de jurisdicție competentă consideră că o parte din prezentul acord este inaplicabilă, restul acestui acord va continua să fie în vigoare și să producă efecte.

COMPLETAREA ACORDULUI

Prezentul Acord constituie întregul acord între părți cu privire la utilizarea SOFTWARE-ului și a oricăror materiale scrise însoțitoare și înlocuiește toate înțelegerile sau înțelegerile anterioare sau contemporane, în scris sau oral, referitoare la obiectul prezentului Acord. Nicio modificare sau revizuire a acestui Acord nu va fi obligatorie decât în scris și semnată de un reprezentant complet autorizat al Yamaha.


Mai este necesar