RIVAGE PM Firmware V3.04 (Previous version)

It was discovered that current scene mix data might return to the default settings if the USER DEFINED key or GPI was used to execute INC RECALL or DEC RECALL after a scene was deleted. This problem occurs only on RIVAGE PM firmware version 3.00 or later.
This problem does not occur if a scene is recalled or stored by any other methods even after a scene is deleted. However, we do not recommend deleting a scene during shows.

RIVAGE PM Firmware / Editor / StageMix Compatibility

Please make sure to match all versions of CS-R10, CS-R10-S, CSD-R7, DSP-R10, RPio622, RPio222, RIVAGE PM Editor and RIVAGE PM StageMix when you operate the RIVAGE PM system. Using an unsupported Editor/firmware combination may result in unexpected behavior.
When updating, a TWINLANe network card (HY256-TL, HY256-TL-SMF) must be installed into the corresponding slot in order to update them simultaneously. If any additional cards are installed after performing the update, please execute the update program again.
For a Dante card (HY144-D, HY144-D-SRC), use the Dante Firmware Update Manager to perform the update.

RIVAGE PM/CL/QL/R/Tio Compatibility

Fixed Bugs in V3.04

  • Solved a rare problem which could occur after scenes or libraries were stored or updated many times in a short period of time. The "DSP Disconnected!" message was shown and no further change could be made to the DSPs.
  • Solved an unlikely problem in which the "Scene empty!" message was shown and a scene could not be recalled.
  • Solved a problem in which executing UPDATE UNDO after a scene was updated and another scene was recalled would overwrite the currently recalled scene with the data before the update and the corresponding scene would not revert to the previous settings.
  • Solved a problem in which the "Dante communication error" message was shown and HA of the Dante I/O devices could not be controlled while an HY144-D card was in use.
  • Solved a problem in which turning the power ON to CSD-R7 might not start the DSP engine and the "Console DSP not responding! Try updating console firmware." message appeared.
  • Solved a problem in which the Event List would be kept on standby at the beginning of the event list until the next time code event was executed if the time code was once stopped and restarted.
  • Solved a problem in which the CONSOLE LOCK image could no longer be loaded or changed if the CONSOLE LOCK file had been write-protected (indicated by a LOCK icon next to the file).

Fixed Bugs in V3.03

  • Solved a problem in which the Recall Safe function for Plug-in Allocation did not work properly to an outboard insert patch.
  • [RIVAGE PM7] Solved a problem in which an error message, stating that internal DSP has been disconnected, may be incorrectly displayed.

Fixed Bugs in V3.02

  • Solved a problem in which restarting the console while a plug-in output was patched to SUB IN would cause the patch not to function properly.
  • Solved a problem in which the system infrequently crashed when a USER DEFINED key to which a function that required a SEL key operation was assigned was pressed.

Fixed Bugs in V3.01

  • Solved a problem in which the control surface might freeze when channel parameters were copied using the [COPY] and [PASTE] keys in the Selected Channel section.
  • Solved a problem in which rebooting the Rio-D2 series unit whose START UP MODE was set to REFRESH or REFRESH w/o MUTE in the REMOTE ONLY state would not establish the connection to the Rio-D2 series with the message “Connecting” left on the screen.
  • Solved some minor errors.

New features in V3.00

  • Labeling function for device names, slots, and ports of network-connected devices. The labels can be found in locations such as the Patch window.
  • Parameter selection when copying channel parameters. In addition, inserted plug-ins also can be copied when copying channels.
  • Added level metering points (PRE GC and PRE D.GAIN for the INPUT METER).
  • Added the “DaNSe” plug-in, a 6-band noise suppressor “DaNSe” which removes background noise and unwanted reverberation.
  • MixToInput function for signal loopback from MIX/MATRIX busses to input channels.
  • SUB IN function to patch from input channels to output channels.
  • Easy-to-use preset for DCA assigning in the THEATRE MODE.
  • Attenuator for each EQ bank.
  • Display of the EQ type in the EQ graph.
  • Alert message when loading data different from the current system configuration.
  • WITH SYSTEM SETTING button for loading the following settings when loading ALL data.
    • Wordclock setting
    • DANTE SETUP (including device mounting, patching, and port names)
    • RY-Slot settings of RPio622/RPio222 (including card settings)
    • Network settings (HY-Slot and RIVAGE PM StageMix)
    • +48V MASTER
  • Added parameter set items when touching parameters while pressing the [SHIFT] key to set up multiple channels simultaneously.
    • STEREO A/B on and off in input channels and MIX channels
    • Bank links on and off for EQ and Dynamics in the THEATRE MOTE
  • Sort function in the Library screen.
  • Display of the internal latency of the engine related to the Delay Compensation setting.
  • RTA offset function to display in linear fashion.
  • Selection for the [ON] key operation in the SENDS ON FADER mode.
  • Flashing of the ON button of the muted channel by mute group function in the SELECTED CHANNEL VIEW screen or the METER screen.
  • [SHIFT] key settings to select whether the action is applied to each BAY or to all BAYs.
  • Determination via the [ENTER] key instead of the ON button when entering settings via the keyboard.
  • Added assignable functions for the USER DEFINED keys, USER DEFINED knobs, and the [Fn] key.
    • USER DEFINED keys
      • SPECIFIC CH of INPUT A/B
      • BAY ALL for the SET BY SEL, SET NORMAL VALUE, and OSCILLATOR
      • SOLO ON
    • USER DEFINED knobs
      • SPECIFIC CH of CH FADER
    • [Fn] key
      • VSC ON

Improvements in V3.00

  • Operability and visibility of settings on the FOCUS, GLOBAL PASTE and RECALL SAFE screens.
  • Operability of settings on the CUSTOM FADER BANK popup screen.
  • Operability of direction of data synchronization on the DEVICE SYNC screen.
  • Display of the channel name on such as the Patch screen or METER screen to improve operability and visibility.
  • Reduced variation of MIDI/GPI output time in a scene recall.
  • Changed the signal level from a stereo MIX channel to the STEREO bus to nominal when PAN is set to maximum.
  • The last function is displayed when assigning a function to an empty USER DEFINED key or knob.
  • SEND MASTER display will relate to output channel selection.
  • Displayed as "DEVICE NOT SYNCED!" when there is a device that cannot sync in the TWINLANe network.

Fixed Bugs in V3.00

  • Solved a problem in which the variable range of SEND level via the SEND knob of the Selected Channel section might not have been appropriate.
  • Solved a problem in which the FILTER Q indication did not appear on the Selected Channel section when DYNAMICS was set to DE-ESSER.
  • Solved a problem of the THEATRE MODE in which EQ or DYNAMICS differed when channels were paired via a scene recall.
  • Solved a problem in which signals from RPio622/RPio222 might not have been input.
  • Solved a problem in which the console firmware might have frozen when saving or loading the console data to a USB flash drive.
  • Solved a problem in which patched channel names would not appear on the Automixer screen.
  • Solved some minor errors.

Known Issue

  • It was discovered that after exiting the Preview mode, a different scene number flashes in the SCENE field and the SCENE field does not show the current scene number. If this happens, pressing the [INC] and [DEC] keys simultaneously will show the current scene number.
  • If the devices are selected from -ONLINE- DEVICE LIST to change the Dante I/O devices to be mounted, the devices may not become connected and indicate as "Virtual." If "Virtual" is kept showing, unmount the devices and then mount them again.
  • It was discovered that if a Dante device with 33 or more inputs/outputs were mounted to HY144-D/HY144-D-SRC, all the port names could not be obtained. This issue will be fixed in a future version.
  • In rare cases, a “DSP Disconnected!” message could be shown for reasons other than the one shown above. In this situation, take the following course of action:
    1. Re-Sync manually. Check this first for the fastest possible recovery. (Only applies to RIVAGE PM10)
    2. If that doesn’t solve the problem, reset by the [RESET] button on the back of the console (these operations do not mute the audio).

Notices in version updating

  • The project file saving method has been changed from V1.20.
    When loading a project file saved by V1.16 or earlier, the patching of plug-ins may be unintentionally removed. If this happens, manually patch them again.
  • When updating the console’s firmware from V1.20 or earlier, the progress bar may stop at the 14/18 status, or an error may stop the updating process. If this continues for five minutes or longer, turn the power of the console to off and on, and then retry the firmware update.
  • When loading a project file saved by V1.21 and earlier, the RACK Focus status indicator on the SCENE screen may not light even if effect plug-ins or GEQs are the target of Focus Recall. To indicate the Focus status properly, open the SCENE SETUP (FOCUS) pop-up screen once, and then close it. After doing this, save the revised project file to remove this problem in the future.

Notices in version downgrading

  • Do not load a project file saved by V1.51 and later to a system running V1.21 and earlier. When loading, all plug-ins will be un-mounted in all Scenes including the current memory. In this case, re-mounting and setting up of parameters will be required.
  • When downgrading the firmware, be sure to initialize all systems after downgrading.
  • When loading data including the MixToInput settings of the V3.00 system, the MixToInput function will work in RIVAGE PM systems even of less than V3.00. However, be careful of the possibility of unwanted signal loops, etc.

Notices for usage

  • If you recall a Scene in which a very high HA gain was set, from a scene having a low HA gain, even if no signal is patched, a very loud pink noise signal is occasionally output for a few seconds.
  • When a certain type of USB keyboard is connected to the console, the following message may appear:
    You must restart your computer to apply these changes [Restart Now] [Restart Later]
    If this message is shown, remove this USB keyboard. It is not compatible with the console and cannot be used.
  • When a DSP mirroring failover occurs, if the DSP engine B is set to active, the Word Clock master will not change automatically. To prevent audio dropouts, do not turn off the power of the DSP engine A even after a failover occurs.
  • Make sure to connect only the RIVAGE PM Editor and RIVAGE PM StageMix to a network connector for a RIVAGE PM Editor, and not the PM Editor network of a different DSP engine.
  • The channel name LCD cannot display unconfirmed characters such as Japanese kanji used in the Dante channel labels.
  • If you are using a Dante card (HY144-D-SRC) in Synchronous (144io Sync SRC) mode, check the “Enable Sync to External” option only for the card that operates as the master on the Dante network.

ATENŢIE

CITIȚI CU ATENȚIE ACEST ACORD DE LICENȚĂ PENTRU SOFTWARE ("AGREEMENT") ÎNAINTE DE A UTILIZA ACEST SOFTWARE. VĂ ESTE PERMIS DOAR SĂ UTILIZAȚI ACEST PRODUS SOFTWARE ÎN CONFORMITATE CU TERMENII ȘI CONDIȚIILE ACESTUI ACORD. ACEST ACORD SE ÎNCHEIE ÎNTRE DVS. (CA ENTITATE INDIVIDUALĂ SAU LEGALĂ) ȘI YAMAHA CORPORATION ("YAMAHA").

PRIN DESCĂRCAREA SAU INSTALAREA ACESTUI SOFTWARE SAU PRINTR-UN ALT MOD ÎN SCOPUL UTILIZĂRII PERSONALE, SUNTEȚI DE ACORD CU TERMENII ACESTEI LICENȚE. DACĂ NU SUNTEȚI DE ACORD CU TERMENII, NU DESCĂRCĂȚI, INSTALAȚI, COPIAȚI SAU SĂ UTILIZAȚI ALTFEL ACEST SOFTWARE. DACĂ AȚI DESCĂRCAT SAU INSTALAT SOFTWARE-UL ȘI NU SUNTEȚI DE ACORD CU TERMENII, ȘTERGEȚI IMEDIAT SOFTWARE-UL.

ACORDAREA LICENȚEI ȘI A DREPTURILOR DE AUTOR

Yamaha vă acordă astfel dreptul de a utiliza programele și fișierele de date care compun software-ul care însoțește acest Acord și toate programele și fișierele pentru modernizarea unui astfel de software care vi se poate distribui în viitor cu termenii și condițiile atașate (colectiv "SOFTWARE"), numai pe un computer, un instrument muzical sau un echipament pe care îl dețineți sau îl gestionați. Deși dreptul de proprietate asupra mediului de stocare în care este stocat SOFTWARE-ul rămâne în obligativitatea dvs., SOFTWARE-ul propriu-zis este deținut de licențiatorii Yamaha și/sau Yamaha și este protejat de legile în vigoare privind drepturile de autor și de toate prevederile aplicabile tratatului.

RESTRICȚII

  • Este posibil să nu aveți competență în inginerie, dezasamblare, decompilare sau orice altceva ce derivă dintr-o formă de cod sursă a SOFTWARE-ului prin orice tip de metodă.
  • Nu puteți reproduce, modifica, schimba, închiria, transmite prin leasing sau distribui SOFTWARE-ul integral sau parțial sau crea lucrări derivate ale SOFTWARE-ului.
  • Nu este permis să transmiteți SOFTWARE-ul electronic de la un computer la altul sau să partajați SOFTWARE-ul într-o rețea cu alte computere
  • Nu este permis să utilizați SOFTWARE-ul pentru a distribui date sau date ilegale care încalcă politica publică.
  • Nu este permis să inițiați servicii bazate pe utilizarea SOFTWARE-ului fără permisiunea companiei Yamaha Corporation.

Datele protejate prin drepturi de autor, incluzând dar fără a se limita la datele MIDI pentru cântece, obținute prin SOFTWARE, se supun următoarelor restricții pe care trebuie să le respectați.

  • Datele primite prin intermediul SOFTWARE-ului nu pot fi utilizate în scopuri comerciale fără permisiunea proprietarului drepturilor de autor.
  • Datele primite prin SOFTWARE nu pot fi duplicate, transferate sau distribuite sau redate sau difuzate pentru ascultători în public, fără permisiunea proprietarului drepturilor de autor.
  • Criptarea datelor primite prin SOFTWARE nu poate fi eliminată și nici filigranul electronic nu poate fi modificat fără permisiunea proprietarului drepturilor de autor.

REZILIEREA

Dacă o lege privind drepturile de autor sau prevederile prezentului Acord sunt încălcate, Acordul se va încheia în mod automat și imediat fără notificare din partea Yamaha. În urma unei astfel de încetări, trebuie să distrugeți imediat SOFTWARE-ul licențiat, orice documente însoțitoare scrise și toate copiile acestuia.

DESCĂRCARE SOFTWARE

Dacă credeți că procesul de descărcare a fost defectuos, puteți contacta Yamaha, iar Yamaha vă va permite să descărcați din nou SOFTWARE-ul, cu condiția să distrugeți primele copiile sau copiile parțiale ale SOFTWARE-ului obținute prin încercarea de descărcare anterioară. Această permisiune de a descărca din nou nu trebuie să limiteze în niciun fel renunțarea la garanție din Secțiunea 5 de mai jos.

DECLINAREA GARANȚIEI SOFTWARE-ULUI

Recunoașteți în mod expres și sunteți de acord că folosirea SOFTWARE-ului este pe riscul dumneavoastră.. SOFTWARE-ul și documentația aferentă sunt furnizate "CA ATARE" și fără garanții de orice fel. FĂRĂ A SE ADRESA PRIN ORICE ALT TIP DE PROVIZIOANE ALE ACESTUI ACORD, YAMAHA DECLINĂ ÎN MOD EXPRES ORICE GARANȚII PRIVIND SOFTWARE-ULUI, EXPRES ȘI IMPLICIT, INCLUZÂND, DAR FĂRĂ A SE LIMITA LA GARANȚIILE IMPLICITE DE VANDABILITATE, ADECVARE PENTRU UN ANUMIT SCOP ȘI NEÎNCĂLCAREA DREPTURILOR TERȚE. ÎN MOD SPECIFIC, DAR FĂRĂ A SE LIMITA, YAMAHA NU GARANTEAZĂ CĂ SOFTWARE-UL VA RĂSPUNDE CERINȚELOR DUMNEAVOASTRĂ, CĂ FUNCȚIONAREA SOFTWARE-ULUI VA FI NEÎNTRERUPTĂ SAU FĂRĂ EROARE, SAU CĂ DEFECȚIUNILE DIN SOFTWARE VOR FI CORECTATE.

LIMITAREA RĂSPUNDERII

OBLIGAȚIA GENERALĂ A YAMAHA ESTE DE A PERMITE UTILIZAREA SOFTWARE-ULUI ÎN CONFORMITATE CU TERMENII STIPULAȚI. ÎN NICI UN CAZ, YAMAHA NU VA FI RESPONSABILĂ PENTRU DVS. SAU ORICE ALTĂ PERSOANĂ PENTRU ORICE DAUNE, INCLUZÂND, FĂRĂ LIMITARE, DAUNE DIRECTE, INDIRECTE, ACCIDENTALE SAU CONSECUTIVE, CHELTUIELI, PIERDERI, PIERDERI DE DATELE SAU ALTE DAUNE PROVENITE DIN UTILIZARE, INCAPACITATEA DE A UTILIZA SOFTWARE-UL, CHIAR DACĂ YAMAHA SAU UN DISTRIBUITOR AUTORIZAT A FOST INFORMAT DE POSIBILITATEA UNOR ASTFEL DE DAUNE. În niciun caz, răspunderea totală a Yamaha față de dvs. pentru toate daunele, pierderile și cauzele acțiunii (indiferent dacă este contractuală, delictuală sau de altă natură) ce depășesc suma plătită pentru SOFTWARE.

SOFTWARE TERȚI

Software-ul și datele părților terțe ("SOFTWARE TERȚI") pot fi atașate la SOFTWARE. În cazul în care, în materialele scrise sau pe datele electronice care însoțesc Software-ul, Yamaha identifică orice software și date ca SOFTWARE TERȚI, recunoașteți și sunteți de acord că trebuie să respectați prevederile oricărui acord furnizat împreună cu SOFTWARE-UL TERȚI și că partea SOFTWARE-UL TERȚI este responsabilă de orice garanție sau răspundere legată de sau provenind din SOFTWARE-UL TERȚI. Yamaha nu este răspunzătoare în niciun fel pentru SOFTWARE-UL TERȚI sau pentru utilizarea de către dvs.

  • Yamaha nu oferă garanții exprese cu privire la SOFTWARE-UL TERȚI. ÎN PLUS, Yamaha DECLINĂ ÎN MOD EXPRES ORICE GARANȚIE IMEDIATĂ, INCLUSIV, DAR FĂRĂ A SE LIMITA LA GARANȚIILE IMEDIATE DE COMERCIALIZARE ȘI DE ADECVARE PENTRU UN ANUMIT SCOP, ÎN CEEA CE PRIVEȘTE SOFTWARE-UL TERȚI.
  • Yamaha nu vă va furniza niciun service sau serviciu de întreținere cu privire la SOFTWARE-UL TERȚI.
  • Yamaha nu este răspunzătoare în fața dvs. sau a oricărei alte persoane pentru orice daune, inclusiv, fără limitare, daune directe, indirecte, incidentale sau consecutive, cheltuieli, profituri pierdute, date pierdute sau alte daune rezultate din utilizare, utilizarea incorectă sau incapacitatea de a folosi SOFTWARE-UL TERȚI.

NOTIFICAREA DREPTURILOR RESTRICȚIONATE DE GUVERNUL SUA:

Software-ul este un "element comercial", deoarece acest termen este definit la 48 C.F.R. 2.101 (octombrie 1995), constând în "software de calculator comercial" și "documentație comercială de software de calculator", astfel sunt utilizați acești termeni în 48 C.F.R. 12.212 (septembrie 1995). În concordanță cu 48 C.F.R. 12.212 și 48 C.F.R. 227.7202-1 până la 227.72024 (iunie 1995), toți utilizatorii finali din S.U.A. vor achiziționa Software-ul numai cu acele drepturi enunțate în prezentul document.

GENERAL

Prezentul acord va fi interpretat în conformitate cu legea japoneză și va fi guvernat de aceasta fără a se face referire la principiile conflictului între legi. Orice litigiu sau procedură vor fi audiate în fața instanței din Tokyo, Japonia. Dacă, din orice motiv, o instanță de jurisdicție competentă consideră că o parte din prezentul acord este inaplicabilă, restul acestui acord va continua să fie în vigoare și să producă efecte.

COMPLETAREA ACORDULUI

Prezentul Acord constituie întregul acord între părți cu privire la utilizarea SOFTWARE-ului și a oricăror materiale scrise însoțitoare și înlocuiește toate înțelegerile sau înțelegerile anterioare sau contemporane, în scris sau oral, referitoare la obiectul prezentului Acord. Nicio modificare sau revizuire a acestui Acord nu va fi obligatorie decât în scris și semnată de un reprezentant complet autorizat al Yamaha.


Mai este necesar