EMX2 Mixere Active

Locația Distribuitorului autorizat

		EMX2
Outline
I/O	Inputs	TOTAL 10ch : Mono (MIC/LINE):4, Stereo(LINE):3
	Phantom power	CH1, 2 : +30 V
	Outputs	SPEAKERS [L, R], MONITOR OUT [L,R], SUBWOOFER OUT
	Control and others	FOOT SW : Effect Mute on/off
Bus		Stereo: 1, Effect: 1
Input Channel Function	PAD	26 dB (CH1-4)
	Hi-Z	Supported (CH4)
	EQ HIGH	8kHz +15dB / -15dB
	EQ MID	2.5kHz +15dB / -15dB
	EQ LOW	100Hz +15dB / -15dB
On-board processors	DSP	SPX Algorithm Reverb 4 programs, MASTER EQ (SPEECH to MUSIC), Feedback suppressor
On-board amplifiers	Maximum output power @4ohms	1kHz THD+N less than 10% (CEA2006) : 250 W + 250 W, 1kHz THD+N less than 1% : 110 W + 110 W
On-board amplifiers	Maximum output power @8ohms	1kHz THD+N less than 10% (CEA2006) : 170 W + 170 W, 1kHz THD+N less than 1% : 110 W + 110 W
Level Meter		6points (-20, -6, 0 , +3, +6, LIMITER)
General specifications
Frequency response		Input to SPEAKERS : +1 dB/-4 dB (40Hz to 20kHz), Input to MONITOR OUT : +0.5 dB/-1.5 dB (20Hz to 20kHz) , refer to the nominal output level @ 1 kHz
Total harmonic distortion		Input to SPEAKERS : 0.2 % @ 13.8 W (40Hz to 20kHz), 0.4 % @ 23.2W (1kHz), Input to MONITOR OUT : 0.05 % @ +10 dBu (20Hz to 20kHz) 0.009 % @ +20 dBu (1kHz), (THD+N, Measured with 22 kHz LPF)
Hum & noise level	Equivalent input noise	-115 dBu
Hum & noise level	Residual output noise	Input to SPEAKERS : -68 dBu (40Hz to 20kHz, MASTER: min), Input to MONITOR OUT : -99 dBu (20Hz to 20kHz, MONITOR: min)
Crosstalk		-80 dB (1 kHz, Measured with 1 kHz band pass filter)
Protection circuit	Load protection	DC-fault
Protection circuit	Amplifier protection	Over heat protection, Over current protection
Power requirements		AC 100-240V, 50Hz/60Hz
Power consumption		35W (Idle) / 90W (1/8 Power)
Dimensions	W	375 mm (14.8")
	H	147 mm (5.8")
	D	220 mm (8.7")
Net weight		4.2 kg (9.3 lbs.)
Accessories		Owner’s Manual, Technical Specifications, Power Cord (2m)
Options		Foot Switch: FC5, Mic Stand Adaptor: BMS-10A, Rack mount kit RK-EMX2
Others		Operating Temperature : 0 to +40℃

Analog Input Characteristics

Input Jack	MIC/LINE	Hi-Z [CH4]	Actual Load Impedance	For Use with Nominal	Sensitivity ^*1	Nominal	Max. Before Clip	Connector
CH INPUT 1−4	MIC	-	3kΩ	150Ω Mics	-56dBu	-35dBu	-10dBu	CH1, 2 XLR-3-31 ^2 (Balanced) CH3, 4 Combo jack ^3 (Balanced)
CH INPUT 1−4	LINE	-	3kΩ	150Ω Mics	-30dBu	-9dBu	+16dBu
CH INPUT 3−4	MIC	OFF	3kΩ	150Ω Mics	-50dBu	-29dBu	-4dBu
	MIC	ON	1MΩ	10 kΩ Lines	-50dBu	-29dBu	-4dBu
	LINE	OFF	3kΩ	150Ω Lines	-24dBu	-3dBu	+22dBu
	LINE	ON	1MΩ	10kΩ	-24dBu	-3dBu	+22dBu
CH INPUT 5/6- 9/10	-	-	10kΩ	150Ω Lines	-24dBu	-3dBu	+22dBu	CH5/6 Phone jack ^4 (Unbalanced) CH7/8 Phone jack ^4 & RCA pin (Unbalanced) CH9/10 Phone jack ^*4 & Stereo mini jack (Unbalanced)

Output Characteristics

Output Terminal	Actual Source Impedance	For Use with Nominal	Nominal	Max. Before Clip	1kHZ THD+N < 1％	1kHz THD+N < 10％	Connector
SPEAKERS OUT [L,R]	<0.1Ω	4Ω	-	-	110W	250W	Phone Jack ^**
SPEAKERS OUT [L,R]	<0.1Ω	8Ω	-	-	110W	170W	Phone Jack ^**
MONITOR OUT [L,R]	150Ω	10kΩ Lines	+4dBu	+20dBu	-	-	Phone Jack ^*
SUBWOOFER OUT	150Ω	10kΩ Lines	-3dBu	+17dBu	-	-	Phone Jack ^*

*Tip = HOT, Ring = COLD, Sleeve = GND
**Tip = Positive, Sleeve = Negative