CL3 Firmware V3.10 (Previous version)

Use this file to update CL5/3/1 to V3.10. Please read the following instructions before updating.

Caution when updating
  • Use the "cl*_firm310.zip" (* is the model number) when updating.
  • Copy files "CL_SUBP_V310.BIN" and "MCLP3_10.PGM" to the root directory of the USB memory. Follow the instructions on the update guide.
  • You need to update the Dante firmware if you update the CL firmware to V3.10 from V2.04 or older. You can now update the Dante firmware for CL also by using the USB memory starting from this version. This method allows you to update both the firmware and the "CL_SUBP_V310.BIN" and "MCLP3_10.PGM" files together at the same time.
  • If updating from CL V1.61 or older, or if the message "NAME SUB CPU is old" appears after updating to V3.10, copy "CL-MD101.BIN" file in \CL*_firm310/NAME SUB (* is the model number) to the root directory of the USB memory. Follow the instructions on the update guide. This method allows you to update both the Dante firmware and the "CL_SUBP_V310.BIN" and "MCLP3_10.PGM" files together at the same time.
*NOTE*
Before copying files, delete all files with extension .PGM and .BIN if any exists in the root directory of the USB memory. Prior to V3.0, the CL and QL Series used different files when updating, but both files used the same name * "C-MD1.BIN." For this reason, an error may occur during update when the incorrect "C-MD1.BIN" file is used or left in the root directory.
Updating Dante firmware by using a USB memory takes approximately 30 minutes.
  • Please do not use the EEE function (*) of network switches in a Dante network.
  • Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts.
    Therefore we strongly recommend that:
    • 1. If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
    • 2. If you use unmanaged switches, make sure to not use network switches that support
    • * EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.
    Cautions for Dante Firmware
  • You need to update the Dante-MY16-AUD firmware to V3.3.9 or later before using the Dante-MY16-AUD with the CL series.
  • The Dante Firmware Update Manager v1.4.13.2 for Mac does not support Mac OS X 10.6.8. Please use Mac OS X 10.7.5, 10.8.5, 10.9.5 or 10.10.
  • The Dante Firmware Update Manager v1.4.13.2 for Windows does not support Windows XP. Please use Windows 7 or Windows 8/8.1.
  • We found a problem in which the Dante settings might not be properly initialized when the firmware is updated to V3.0/V3.1, which results in data inconsistency between the CL/QL console and the R series units. This might occur only when the Dante Latency was set to 0.25ms or 0.5ms. Therefore, after updating to V3.0/V3.1 it is recommend to briefly change the Latency to 1.0ms on the console with the Console ID #1, then restore the original setting again. This will remove the possible data inconsistency between the console and the mounted R series units. However, Dante Controller will be needed to manually change the settings of R series units that are not mounted on the console with Console ID #1.

CL/QL/RIVAGE/R/Tio Series Editor/Firmware/R Remote Compatibility

Please make sure to use appropriate version of CL Editor or QL Editor which is compatible with your console firmware in reference to the following compatibility chart. Using an unsupported Editor/firmware combination may result in unexpected behavior.
The Firmware Set is a set of main (and sub) firmware of the device and the Dante firmware. The version of Firmware Set is the same as the version of the main firmware. Refer to the release note of each firmware about the details of the Firmware Set.

Compatibility List

  • You can remotely control one RSio64-D unit from a maximum of two CL/QL/R Remote units.
  • You can remotely control one RMio64-D unit from a maximum of six CL/QL/R Remote units.
  • You can remotely control one Rio/Ri/Ro unit from a maximum of two computers operating R Remote. You can also remotely control from four separate CL/QL units.

New Features in V3.10

  • Now supports the RSio64-D control.
  • You can now remotely control supported third-party head amps (HA) from the console.
  • Functions related to cascade connections have been added.
  • You can now select CENTER NOMINAL or LR NOMINAL for the pan setting of monaural input channels.
  • You can now appropriately switch PAN mode and PAN knob settings due to changes in the stereo input signal processing of L-MONO, R-MONO and LR-MONO.
    For details, refer to theCL5/CL3/CL1 V3.10 Supplementary Manual

Improvements

  • You can now update the Dante firmware for CL and QL by using the USB memory.
  • The files for updating CL and QL have been changed from the same name "C-MD1.BIN" to separate names. This will prevent updating with the wrong file.
  • You can now manually remount when the USB memory is not recognized.

Fixed bugs

  • Solved a problem in which the levels were not the same when odd-numbered/even-numbered MIX and MATRIX buses with different levels were linked to use as a stereo bus.
  • Solved a problem in which if GPI OUT was set for the current scene, GPI operated when the scene was recalled by using PREVIEW mode.
  • Solved a problem in which if GPI OUT was set for that scene after storing a scene, GPI OUT was output also when a library was recalled.
  • Solved a problem in which it appeared that RMio64-D, as a member of the NUAGE Workgroup Manager, could operate from CL. (In actuality, you cannot operate from CL while it is a member of the NUAGE Workgroup Manager.)

Known issue

  • If Dante Virtual Soundcard (DVS) is patched to the CL series device using Dante Controller, the patching may not be recalled correctly when the CL series device is restarted. In such cases, patch the DVS again. In addition, when using a version of DVS for Windows that is older than v3.2.0, patches after CH41 cannot be performed from CL series consoles.
  • If the SECONDARY PORT setting (REDUNDANT/DAISY CHAIN) of the Dante audio network would not change while the Dante device is not connected with Dante PRIMARY/SECONDARY connectors, no audio signal will pass. Audio will once again pass after the Dante device is connected or after the power for CL has been restarted.
  • Loading of a file created by version V1.15 or older will not include the mount information of Dante devices other than any connected R-series. It is the same when recalling a DANTE INPUT PATCH LIBRARY. Please reset MOUNT, PATCH, and DANTE INPUT PATCH Library data using V1.51 or later if necessary.

NOTICE

  • When setting up the latency in Dante Controller, and there is a discrepancy in latency with the transmit device or the receive device, the largest (slowest) latency setting becomes effective.
  • The following device labels are used for detecting a SUPPORTED DEVICE.
    • Y###-**********
      # is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)
      *indicates any desired character (alphabetical uppercase or lowercase, numerals, or -(hyphen) may be used) Up to 31 characters including the 'Y' are supported.
      For the R-series, make sure that the ID indicated by Y###- is not duplicated by any other R-series unit, even if it is a different size.
  • In V2.0 and later, custom fader bank settings are not only included in user settings, but in scene data as well. The custom fader bank settings that are called up vary depending on the logged-in user, the type of the loaded data, and the version. Please note the following points:
    • If you load console data of the ALL type as Administrator, the custom fader bank settings for the saved Administrator are recalled. If you load ALL data as Guest or another user, the custom fader bank settings for the saved current scene are called up.
    • If you load ALL data that was saved in CL V1.70 or earlier, since scenes do not include custom fader bank settings, the custom fader bank settings for the current scene when the load was performed are applied to all scenes. Therefore, before loading ALL data, we recommend that you either change users to set the custom fader bank to the desired setting, or that you enable Recall Safe for the custom fader bank.
  • File Converter V3.0.0, compatible with CL firmware V2.00, V3.00 and V3.10, and QL firmware V3.00 and V3.10, has been made available for use.

ATENŢIE

CITIȚI CU ATENȚIE ACEST ACORD DE LICENȚĂ PENTRU SOFTWARE ("AGREEMENT") ÎNAINTE DE A UTILIZA ACEST SOFTWARE. VĂ ESTE PERMIS DOAR SĂ UTILIZAȚI ACEST PRODUS SOFTWARE ÎN CONFORMITATE CU TERMENII ȘI CONDIȚIILE ACESTUI ACORD. ACEST ACORD SE ÎNCHEIE ÎNTRE DVS. (CA ENTITATE INDIVIDUALĂ SAU LEGALĂ) ȘI YAMAHA CORPORATION ("YAMAHA").

PRIN DESCĂRCAREA SAU INSTALAREA ACESTUI SOFTWARE SAU PRINTR-UN ALT MOD ÎN SCOPUL UTILIZĂRII PERSONALE, SUNTEȚI DE ACORD CU TERMENII ACESTEI LICENȚE. DACĂ NU SUNTEȚI DE ACORD CU TERMENII, NU DESCĂRCĂȚI, INSTALAȚI, COPIAȚI SAU SĂ UTILIZAȚI ALTFEL ACEST SOFTWARE. DACĂ AȚI DESCĂRCAT SAU INSTALAT SOFTWARE-UL ȘI NU SUNTEȚI DE ACORD CU TERMENII, ȘTERGEȚI IMEDIAT SOFTWARE-UL.

ACORDAREA LICENȚEI ȘI A DREPTURILOR DE AUTOR

Yamaha vă acordă astfel dreptul de a utiliza programele și fișierele de date care compun software-ul care însoțește acest Acord și toate programele și fișierele pentru modernizarea unui astfel de software care vi se poate distribui în viitor cu termenii și condițiile atașate (colectiv "SOFTWARE"), numai pe un computer, un instrument muzical sau un echipament pe care îl dețineți sau îl gestionați. Deși dreptul de proprietate asupra mediului de stocare în care este stocat SOFTWARE-ul rămâne în obligativitatea dvs., SOFTWARE-ul propriu-zis este deținut de licențiatorii Yamaha și/sau Yamaha și este protejat de legile în vigoare privind drepturile de autor și de toate prevederile aplicabile tratatului.

RESTRICȚII

  • Este posibil să nu aveți competență în inginerie, dezasamblare, decompilare sau orice altceva ce derivă dintr-o formă de cod sursă a SOFTWARE-ului prin orice tip de metodă.
  • Nu puteți reproduce, modifica, schimba, închiria, transmite prin leasing sau distribui SOFTWARE-ul integral sau parțial sau crea lucrări derivate ale SOFTWARE-ului.
  • Nu este permis să transmiteți SOFTWARE-ul electronic de la un computer la altul sau să partajați SOFTWARE-ul într-o rețea cu alte computere
  • Nu este permis să utilizați SOFTWARE-ul pentru a distribui date sau date ilegale care încalcă politica publică.
  • Nu este permis să inițiați servicii bazate pe utilizarea SOFTWARE-ului fără permisiunea companiei Yamaha Corporation.

Datele protejate prin drepturi de autor, incluzând dar fără a se limita la datele MIDI pentru cântece, obținute prin SOFTWARE, se supun următoarelor restricții pe care trebuie să le respectați.

  • Datele primite prin intermediul SOFTWARE-ului nu pot fi utilizate în scopuri comerciale fără permisiunea proprietarului drepturilor de autor.
  • Datele primite prin SOFTWARE nu pot fi duplicate, transferate sau distribuite sau redate sau difuzate pentru ascultători în public, fără permisiunea proprietarului drepturilor de autor.
  • Criptarea datelor primite prin SOFTWARE nu poate fi eliminată și nici filigranul electronic nu poate fi modificat fără permisiunea proprietarului drepturilor de autor.

REZILIEREA

Dacă o lege privind drepturile de autor sau prevederile prezentului Acord sunt încălcate, Acordul se va încheia în mod automat și imediat fără notificare din partea Yamaha. În urma unei astfel de încetări, trebuie să distrugeți imediat SOFTWARE-ul licențiat, orice documente însoțitoare scrise și toate copiile acestuia.

DESCĂRCARE SOFTWARE

Dacă credeți că procesul de descărcare a fost defectuos, puteți contacta Yamaha, iar Yamaha vă va permite să descărcați din nou SOFTWARE-ul, cu condiția să distrugeți primele copiile sau copiile parțiale ale SOFTWARE-ului obținute prin încercarea de descărcare anterioară. Această permisiune de a descărca din nou nu trebuie să limiteze în niciun fel renunțarea la garanție din Secțiunea 5 de mai jos.

DECLINAREA GARANȚIEI SOFTWARE-ULUI

Recunoașteți în mod expres și sunteți de acord că folosirea SOFTWARE-ului este pe riscul dumneavoastră.. SOFTWARE-ul și documentația aferentă sunt furnizate "CA ATARE" și fără garanții de orice fel. FĂRĂ A SE ADRESA PRIN ORICE ALT TIP DE PROVIZIOANE ALE ACESTUI ACORD, YAMAHA DECLINĂ ÎN MOD EXPRES ORICE GARANȚII PRIVIND SOFTWARE-ULUI, EXPRES ȘI IMPLICIT, INCLUZÂND, DAR FĂRĂ A SE LIMITA LA GARANȚIILE IMPLICITE DE VANDABILITATE, ADECVARE PENTRU UN ANUMIT SCOP ȘI NEÎNCĂLCAREA DREPTURILOR TERȚE. ÎN MOD SPECIFIC, DAR FĂRĂ A SE LIMITA, YAMAHA NU GARANTEAZĂ CĂ SOFTWARE-UL VA RĂSPUNDE CERINȚELOR DUMNEAVOASTRĂ, CĂ FUNCȚIONAREA SOFTWARE-ULUI VA FI NEÎNTRERUPTĂ SAU FĂRĂ EROARE, SAU CĂ DEFECȚIUNILE DIN SOFTWARE VOR FI CORECTATE.

LIMITAREA RĂSPUNDERII

OBLIGAȚIA GENERALĂ A YAMAHA ESTE DE A PERMITE UTILIZAREA SOFTWARE-ULUI ÎN CONFORMITATE CU TERMENII STIPULAȚI. ÎN NICI UN CAZ, YAMAHA NU VA FI RESPONSABILĂ PENTRU DVS. SAU ORICE ALTĂ PERSOANĂ PENTRU ORICE DAUNE, INCLUZÂND, FĂRĂ LIMITARE, DAUNE DIRECTE, INDIRECTE, ACCIDENTALE SAU CONSECUTIVE, CHELTUIELI, PIERDERI, PIERDERI DE DATELE SAU ALTE DAUNE PROVENITE DIN UTILIZARE, INCAPACITATEA DE A UTILIZA SOFTWARE-UL, CHIAR DACĂ YAMAHA SAU UN DISTRIBUITOR AUTORIZAT A FOST INFORMAT DE POSIBILITATEA UNOR ASTFEL DE DAUNE. În niciun caz, răspunderea totală a Yamaha față de dvs. pentru toate daunele, pierderile și cauzele acțiunii (indiferent dacă este contractuală, delictuală sau de altă natură) ce depășesc suma plătită pentru SOFTWARE.

SOFTWARE TERȚI

Software-ul și datele părților terțe ("SOFTWARE TERȚI") pot fi atașate la SOFTWARE. În cazul în care, în materialele scrise sau pe datele electronice care însoțesc Software-ul, Yamaha identifică orice software și date ca SOFTWARE TERȚI, recunoașteți și sunteți de acord că trebuie să respectați prevederile oricărui acord furnizat împreună cu SOFTWARE-UL TERȚI și că partea SOFTWARE-UL TERȚI este responsabilă de orice garanție sau răspundere legată de sau provenind din SOFTWARE-UL TERȚI. Yamaha nu este răspunzătoare în niciun fel pentru SOFTWARE-UL TERȚI sau pentru utilizarea de către dvs.

  • Yamaha nu oferă garanții exprese cu privire la SOFTWARE-UL TERȚI. ÎN PLUS, Yamaha DECLINĂ ÎN MOD EXPRES ORICE GARANȚIE IMEDIATĂ, INCLUSIV, DAR FĂRĂ A SE LIMITA LA GARANȚIILE IMEDIATE DE COMERCIALIZARE ȘI DE ADECVARE PENTRU UN ANUMIT SCOP, ÎN CEEA CE PRIVEȘTE SOFTWARE-UL TERȚI.
  • Yamaha nu vă va furniza niciun service sau serviciu de întreținere cu privire la SOFTWARE-UL TERȚI.
  • Yamaha nu este răspunzătoare în fața dvs. sau a oricărei alte persoane pentru orice daune, inclusiv, fără limitare, daune directe, indirecte, incidentale sau consecutive, cheltuieli, profituri pierdute, date pierdute sau alte daune rezultate din utilizare, utilizarea incorectă sau incapacitatea de a folosi SOFTWARE-UL TERȚI.

NOTIFICAREA DREPTURILOR RESTRICȚIONATE DE GUVERNUL SUA:

Software-ul este un "element comercial", deoarece acest termen este definit la 48 C.F.R. 2.101 (octombrie 1995), constând în "software de calculator comercial" și "documentație comercială de software de calculator", astfel sunt utilizați acești termeni în 48 C.F.R. 12.212 (septembrie 1995). În concordanță cu 48 C.F.R. 12.212 și 48 C.F.R. 227.7202-1 până la 227.72024 (iunie 1995), toți utilizatorii finali din S.U.A. vor achiziționa Software-ul numai cu acele drepturi enunțate în prezentul document.

GENERAL

Prezentul acord va fi interpretat în conformitate cu legea japoneză și va fi guvernat de aceasta fără a se face referire la principiile conflictului între legi. Orice litigiu sau procedură vor fi audiate în fața instanței din Tokyo, Japonia. Dacă, din orice motiv, o instanță de jurisdicție competentă consideră că o parte din prezentul acord este inaplicabilă, restul acestui acord va continua să fie în vigoare și să producă efecte.

COMPLETAREA ACORDULUI

Prezentul Acord constituie întregul acord între părți cu privire la utilizarea SOFTWARE-ului și a oricăror materiale scrise însoțitoare și înlocuiește toate înțelegerile sau înțelegerile anterioare sau contemporane, în scris sau oral, referitoare la obiectul prezentului Acord. Nicio modificare sau revizuire a acestui Acord nu va fi obligatorie decât în scris și semnată de un reprezentant complet autorizat al Yamaha.