QL1 Firmware V4.50 (Previous version)

With CL/QL series V4.50 and RIVAGE PM series V2.02, we found that Dante Virtual Soundcard (DVS) V4.0.3.1 or later cannot be recognized as a "SUPPORTED DEVICE" on these consoles. In order to work around this for the time being, we recommend to follow the operation rules below.

Temporary Operations

  • Use earlier versions of DVS than V4.0.3.1.
  • When using V4.0.3.1 or a later version of DVS,
    • mount DVS as an UNSUPPORTED DEVICE, and make the Dante patches from the console or Dante Controller.
    • if NUENDO Live is to be controlled from the CL/QL consoles remotely, in the NUENDO Live Setup view, set the IP address of the PC not from the "DVS" tab, but from the "SPECIFIED IP ADDRESS" tab.

Use this release notes to update CL/QL to V4.50. Please read the following instructions before updating.

Caution when updating

  • Use the "ql*_firm450.zip "(* is the model number)when updating.
  • Copy file "MQLP4_50.PGM" to the root directory of the USB memory. Follow the instructions on the update guide.
  • You also need to update the Dante firmware. You can now update the Dante firmware for QL also by using the USB memory. This method allows you to update both the firmware and the "MQLP4_50.PGM" file together at the same time.
  • If the message "NAME SUB CPU is old" appears after updating to V4.50, copy "QL-MD103.BIN" file in QL*_firm450/NAME SUB (* is the model number) to the root directory of the USB memory. Follow the instructions on the update guide. This method allows you to update both the Dante firmware and the "MQLP4_50.PGM" files together at the same time.

*IMPORTANT NOTE*

  • Before copying files, delete all files with extension .PGM and .BIN if any exists in the root directory of the USB memory. Prior to V3.0, the CL and QL Series used different files when updating, but both files used the same name * "QL-MD103.BIN." For this reason, an error may occur during update when the incorrect "QL-MD103.BIN" file is used or left in the root directory.
  • Updating Dante firmware by using a USB memory takes approximately 30 minutes.

Please do not use the EEE function (*) of network switches in a Dante network.

Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts.

Therefore we strongly recommend that:

  1. If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
  2. If you use unmanaged switches, make sure to not use network switches that support EEE.

* EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.

Cautions for Dante Firmware

  • You need to update the Dante-MY16-AUD firmware to V3.3.9 or later before using the Dante-MY16-AUD with the QL series.
  • The Dante Firmware Update Manager since v1.4.16.6 for Windows does not support Windows XP. Please use Windows 7, Windows 8.1, or Windows 10.
  • When updating, refer to “QL5/QL1 Firmware Update Guide.”
  • The Dante settings might not be properly initialized when the firmware is updated, which results in data inconsistency between the CL/QL console and the R series units. This might occur only when the Dante Latency was set to 0.25ms or 0.5ms. Therefore, after updating, it is recommend to briefly change the Latency to 1.0ms on the console with the Console ID #1, then restore the original setting again. This will remove the possible data inconsistency between the console and the mounted R series units. However, Dante Controller will be needed to manually change the settings of R series units that are not mounted on the console with Console ID #1.

CL/QL/RIVAGE/R/Tio Series Editor/Firmware/R Remote Compatibility

Please make sure to use appropriate version of CL Editor or QL Editor which is compatible with your console firmware in reference to the following compatibility chart. Using an unsupported Editor/firmware combination may result in unexpected behavior.
The Firmware Set is a set of main (and sub) firmware of the device and the Dante firmware. The version of Firmware Set is the same as the version of the main firmware. Refer to the release note of each firmware about the details of the Firmware Set.

Compatibility List

New features in V4.50

  • Now supports the Dante Domain Manager.
  • Now supports the Rio3224-D2 and Rio1608-D2.

Improvements in V4.50

  • The Dante status display has been improved.
  • The Premium Rack Edit screen will remain open when recalling a Scene selected the same module. In previous versions, the Edit screen was closed when a Scene was recalled.

Fixed bugs in V4.50

  • Solved a problem in which, when you change the configuration of the Dante network under specific conditions, an error message is displayed and the unit needs to be restarted.
  • Solved a problem in which audio signal is output at unity level momentarily when you operate mute channel ON/OFF or CUE while DCA muting the INPUT BUS/MIX BUS that is being sent to MATRIX 7/8.
  • Solved a problem in which the sound of the OpenDeck Plug-in does not sound under the initial setting.
  • Solved a problem in which the High band gain is set to 0 dB when loading an EQ Library made before V4 and earlier.
  • Solved a problem that changes are not reflected in the EQ graph of Overview when the Band Bypass of EQ is changed.
  • Solved a problem in which StageMx cannot be synchronized if offset is applied to CH LINK in such as RECALL SAFE for a stereo MIX BUS etc. set via the BUS SETUP.
  • Solved a problem in which the clock was changed to INT48K when switching the clock from Dante to external input under V4.1.
  • Solved a problem in which setting changes cannot be finished when the UNIT ID and the SECONDARY are changed at the same time.
  • Solved a problem in which the CL/QL unit may become inappropriate due to misrecognitions, or due to poor contact etc., when inserting a USB memory.
  • Solved a problem in which “No response from I/O device” message was displayed incorrectly.
  • Solved a problem in which CUE CLEAR of the QL unit also cleared CUE B when setting the CUE B to Remote mode.
  • Solved a problem in which the [Next]/[Prev] functions set with USER DEFINED Keys did not work when closing the RECORDER screen.

Known issue

  • If Dante Virtual Soundcard (DVS) is patched to the QL series device using Dante Controller, the patching may not be recalled correctly when the QL series device is restarted. In such cases, patch the DVS again. In addition, when using a version of DVS for Windows that is older than v3.2.0, patches after CH41 cannot be performed from QL series consoles.
  • Loading of a file created by version V1.15 or older will not include the mount information of Dante devices other than any connected R-series. It is the same when recalling a DANTE INPUT PATCH LIBRARY. Please reset MOUNT, PATCH, and DANTE INPUT PATCH Library data using V1.51 or later if necessary.
  • When a power redundant error occurs in the Rio3224-D2/Rio1608-D2, the SYSTEM/SYNC error message on the CL/QL unit mounted to the Rio3224-D2/Rio1608-D2 is incorrectly displayed as “DANTE SETTING MISMATCH.”

NOTICE

  • You can use the following amount of CL/QL/R Remote units to remotely control each device unit (listed at left).
    RSio64-D/Tio1608-D: Maximum of two CL/QL/R Remote units.
    RMio64-D: Maximum of six CL/QL/R Remote units.
    Rio/Ri/Ro: Maximum of four CL/QL units plus two separate computers operating R Remote.
    Rio3224-D2/Rio1608-D2: Maximum of four CL/QL units plus five separate computers operating R Remote.
  • You can connect maximum of ten iOS devices operating MonitorMix.
  • When setting up the latency in Dante Controller, and there is a discrepancy in latency with the transmit device or the receive device, the largest (slowest) latency setting becomes effective.
  • The following device labels are used for detecting a SUPPORTED DEVICE. (Except Dante non-supported devices)
    Y###-**********
    # is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)
    * indicates any desired character (alphabetical uppercase or lowercase, numerals, or -(hyphen) may be used) Up to 31 characters including the 'Y' are supported.
    For the R-series, make sure that the ID indicated by Y###- is not duplicated by any other R-series unit, even if it is a different size.
  • In V2.0 and later, custom fader bank settings are not only included in user settings, but in scene data as well. The custom fader bank settings that are called up vary depending on the logged-in user, the type of the loaded data, and the version. Please note the following points:
    If you load console data of the ALL type as Administrator, the custom fader bank settings for the saved Administrator are recalled. If you load ALL data as Guest or another user, the custom fader bank settings for the saved current scene are called up.
    If you load ALL data that was saved in QL V1.70 or earlier, since scenes do not include custom fader bank settings, the custom fader bank settings for the current scene when the load was performed are applied to all scenes. Therefore, before loading ALL data, we recommend that you either change users to set the custom fader bank to the desired setting, or that you enable Recall Safe for the custom fader bank.
  • File Converter V4.0.0, compatible with CL firmware V2.xx, V3.xx, and V4.xx and QL firmware V3.xx and V4.xx has been made available for use.

ATENŢIE

CITIȚI CU ATENȚIE ACEST ACORD DE LICENȚĂ PENTRU SOFTWARE ("AGREEMENT") ÎNAINTE DE A UTILIZA ACEST SOFTWARE. VĂ ESTE PERMIS DOAR SĂ UTILIZAȚI ACEST PRODUS SOFTWARE ÎN CONFORMITATE CU TERMENII ȘI CONDIȚIILE ACESTUI ACORD. ACEST ACORD SE ÎNCHEIE ÎNTRE DVS. (CA ENTITATE INDIVIDUALĂ SAU LEGALĂ) ȘI YAMAHA CORPORATION ("YAMAHA").

PRIN DESCĂRCAREA SAU INSTALAREA ACESTUI SOFTWARE SAU PRINTR-UN ALT MOD ÎN SCOPUL UTILIZĂRII PERSONALE, SUNTEȚI DE ACORD CU TERMENII ACESTEI LICENȚE. DACĂ NU SUNTEȚI DE ACORD CU TERMENII, NU DESCĂRCĂȚI, INSTALAȚI, COPIAȚI SAU SĂ UTILIZAȚI ALTFEL ACEST SOFTWARE. DACĂ AȚI DESCĂRCAT SAU INSTALAT SOFTWARE-UL ȘI NU SUNTEȚI DE ACORD CU TERMENII, ȘTERGEȚI IMEDIAT SOFTWARE-UL.

ACORDAREA LICENȚEI ȘI A DREPTURILOR DE AUTOR

Yamaha vă acordă astfel dreptul de a utiliza programele și fișierele de date care compun software-ul care însoțește acest Acord și toate programele și fișierele pentru modernizarea unui astfel de software care vi se poate distribui în viitor cu termenii și condițiile atașate (colectiv "SOFTWARE"), numai pe un computer, un instrument muzical sau un echipament pe care îl dețineți sau îl gestionați. Deși dreptul de proprietate asupra mediului de stocare în care este stocat SOFTWARE-ul rămâne în obligativitatea dvs., SOFTWARE-ul propriu-zis este deținut de licențiatorii Yamaha și/sau Yamaha și este protejat de legile în vigoare privind drepturile de autor și de toate prevederile aplicabile tratatului.

RESTRICȚII

  • Este posibil să nu aveți competență în inginerie, dezasamblare, decompilare sau orice altceva ce derivă dintr-o formă de cod sursă a SOFTWARE-ului prin orice tip de metodă.
  • Nu puteți reproduce, modifica, schimba, închiria, transmite prin leasing sau distribui SOFTWARE-ul integral sau parțial sau crea lucrări derivate ale SOFTWARE-ului.
  • Nu este permis să transmiteți SOFTWARE-ul electronic de la un computer la altul sau să partajați SOFTWARE-ul într-o rețea cu alte computere
  • Nu este permis să utilizați SOFTWARE-ul pentru a distribui date sau date ilegale care încalcă politica publică.
  • Nu este permis să inițiați servicii bazate pe utilizarea SOFTWARE-ului fără permisiunea companiei Yamaha Corporation.

Datele protejate prin drepturi de autor, incluzând dar fără a se limita la datele MIDI pentru cântece, obținute prin SOFTWARE, se supun următoarelor restricții pe care trebuie să le respectați.

  • Datele primite prin intermediul SOFTWARE-ului nu pot fi utilizate în scopuri comerciale fără permisiunea proprietarului drepturilor de autor.
  • Datele primite prin SOFTWARE nu pot fi duplicate, transferate sau distribuite sau redate sau difuzate pentru ascultători în public, fără permisiunea proprietarului drepturilor de autor.
  • Criptarea datelor primite prin SOFTWARE nu poate fi eliminată și nici filigranul electronic nu poate fi modificat fără permisiunea proprietarului drepturilor de autor.

REZILIEREA

Dacă o lege privind drepturile de autor sau prevederile prezentului Acord sunt încălcate, Acordul se va încheia în mod automat și imediat fără notificare din partea Yamaha. În urma unei astfel de încetări, trebuie să distrugeți imediat SOFTWARE-ul licențiat, orice documente însoțitoare scrise și toate copiile acestuia.

DESCĂRCARE SOFTWARE

Dacă credeți că procesul de descărcare a fost defectuos, puteți contacta Yamaha, iar Yamaha vă va permite să descărcați din nou SOFTWARE-ul, cu condiția să distrugeți primele copiile sau copiile parțiale ale SOFTWARE-ului obținute prin încercarea de descărcare anterioară. Această permisiune de a descărca din nou nu trebuie să limiteze în niciun fel renunțarea la garanție din Secțiunea 5 de mai jos.

DECLINAREA GARANȚIEI SOFTWARE-ULUI

Recunoașteți în mod expres și sunteți de acord că folosirea SOFTWARE-ului este pe riscul dumneavoastră.. SOFTWARE-ul și documentația aferentă sunt furnizate "CA ATARE" și fără garanții de orice fel. FĂRĂ A SE ADRESA PRIN ORICE ALT TIP DE PROVIZIOANE ALE ACESTUI ACORD, YAMAHA DECLINĂ ÎN MOD EXPRES ORICE GARANȚII PRIVIND SOFTWARE-ULUI, EXPRES ȘI IMPLICIT, INCLUZÂND, DAR FĂRĂ A SE LIMITA LA GARANȚIILE IMPLICITE DE VANDABILITATE, ADECVARE PENTRU UN ANUMIT SCOP ȘI NEÎNCĂLCAREA DREPTURILOR TERȚE. ÎN MOD SPECIFIC, DAR FĂRĂ A SE LIMITA, YAMAHA NU GARANTEAZĂ CĂ SOFTWARE-UL VA RĂSPUNDE CERINȚELOR DUMNEAVOASTRĂ, CĂ FUNCȚIONAREA SOFTWARE-ULUI VA FI NEÎNTRERUPTĂ SAU FĂRĂ EROARE, SAU CĂ DEFECȚIUNILE DIN SOFTWARE VOR FI CORECTATE.

LIMITAREA RĂSPUNDERII

OBLIGAȚIA GENERALĂ A YAMAHA ESTE DE A PERMITE UTILIZAREA SOFTWARE-ULUI ÎN CONFORMITATE CU TERMENII STIPULAȚI. ÎN NICI UN CAZ, YAMAHA NU VA FI RESPONSABILĂ PENTRU DVS. SAU ORICE ALTĂ PERSOANĂ PENTRU ORICE DAUNE, INCLUZÂND, FĂRĂ LIMITARE, DAUNE DIRECTE, INDIRECTE, ACCIDENTALE SAU CONSECUTIVE, CHELTUIELI, PIERDERI, PIERDERI DE DATELE SAU ALTE DAUNE PROVENITE DIN UTILIZARE, INCAPACITATEA DE A UTILIZA SOFTWARE-UL, CHIAR DACĂ YAMAHA SAU UN DISTRIBUITOR AUTORIZAT A FOST INFORMAT DE POSIBILITATEA UNOR ASTFEL DE DAUNE. În niciun caz, răspunderea totală a Yamaha față de dvs. pentru toate daunele, pierderile și cauzele acțiunii (indiferent dacă este contractuală, delictuală sau de altă natură) ce depășesc suma plătită pentru SOFTWARE.

SOFTWARE TERȚI

Software-ul și datele părților terțe ("SOFTWARE TERȚI") pot fi atașate la SOFTWARE. În cazul în care, în materialele scrise sau pe datele electronice care însoțesc Software-ul, Yamaha identifică orice software și date ca SOFTWARE TERȚI, recunoașteți și sunteți de acord că trebuie să respectați prevederile oricărui acord furnizat împreună cu SOFTWARE-UL TERȚI și că partea SOFTWARE-UL TERȚI este responsabilă de orice garanție sau răspundere legată de sau provenind din SOFTWARE-UL TERȚI. Yamaha nu este răspunzătoare în niciun fel pentru SOFTWARE-UL TERȚI sau pentru utilizarea de către dvs.

  • Yamaha nu oferă garanții exprese cu privire la SOFTWARE-UL TERȚI. ÎN PLUS, Yamaha DECLINĂ ÎN MOD EXPRES ORICE GARANȚIE IMEDIATĂ, INCLUSIV, DAR FĂRĂ A SE LIMITA LA GARANȚIILE IMEDIATE DE COMERCIALIZARE ȘI DE ADECVARE PENTRU UN ANUMIT SCOP, ÎN CEEA CE PRIVEȘTE SOFTWARE-UL TERȚI.
  • Yamaha nu vă va furniza niciun service sau serviciu de întreținere cu privire la SOFTWARE-UL TERȚI.
  • Yamaha nu este răspunzătoare în fața dvs. sau a oricărei alte persoane pentru orice daune, inclusiv, fără limitare, daune directe, indirecte, incidentale sau consecutive, cheltuieli, profituri pierdute, date pierdute sau alte daune rezultate din utilizare, utilizarea incorectă sau incapacitatea de a folosi SOFTWARE-UL TERȚI.

NOTIFICAREA DREPTURILOR RESTRICȚIONATE DE GUVERNUL SUA:

Software-ul este un "element comercial", deoarece acest termen este definit la 48 C.F.R. 2.101 (octombrie 1995), constând în "software de calculator comercial" și "documentație comercială de software de calculator", astfel sunt utilizați acești termeni în 48 C.F.R. 12.212 (septembrie 1995). În concordanță cu 48 C.F.R. 12.212 și 48 C.F.R. 227.7202-1 până la 227.72024 (iunie 1995), toți utilizatorii finali din S.U.A. vor achiziționa Software-ul numai cu acele drepturi enunțate în prezentul document.

GENERAL

Prezentul acord va fi interpretat în conformitate cu legea japoneză și va fi guvernat de aceasta fără a se face referire la principiile conflictului între legi. Orice litigiu sau procedură vor fi audiate în fața instanței din Tokyo, Japonia. Dacă, din orice motiv, o instanță de jurisdicție competentă consideră că o parte din prezentul acord este inaplicabilă, restul acestui acord va continua să fie în vigoare și să producă efecte.

COMPLETAREA ACORDULUI

Prezentul Acord constituie întregul acord între părți cu privire la utilizarea SOFTWARE-ului și a oricăror materiale scrise însoțitoare și înlocuiește toate înțelegerile sau înțelegerile anterioare sau contemporane, în scris sau oral, referitoare la obiectul prezentului Acord. Nicio modificare sau revizuire a acestui Acord nu va fi obligatorie decât în scris și semnată de un reprezentant complet autorizat al Yamaha.