MTX Editor V1.2.2 for Win8.1/8/7 and firmware V1.20 (Previous version)

• To update the firmware, please refer to the MTX/XMV/EXi8/EXo8 Firmware Update Guide.
• The preset data of the device will be lost if the firmware is updated from V1.0x, V1.1x to V1.2x or later. Please ensure that the MTX is synchronized and saved to the compatible MTX Editor as a project file before performing the firmware update in order to ensure that your project data is not lost, and then perform the firmware upgrade using the latest version of MTX Editor. Please ensure that the device is initialized after the update, then open the previously saved project file using the latest MTX Editor and re-synchronize to the updated devices.
• When initializing Dante devices (MTX5-D and Dante model of XMV), please ensure that all other Dante devices on the network are disconnected or powered off. Otherwise initialization could take longer than necessary.
• To prevent damage to the SD memory card as well as loss of data, do not remove or insert the SD memory card while the device is on.
• Although MTX Editor shows 'Completed' after updating firmware, please do not turn off the power of the device until the indicators on the front panel have stopped blinking.
• In the unlikely case of hardware failure, please initialize the replacement device(s) and confirm proper ID and DIP switch settings, then resynchronize from MTX Editor to the device(s).
• When entering text into a text field inside a dialog box of MTX Editor using Input Method Editors, such as Microsoft IME, please ensure that the mouse pointer is not clicked over another area of the open dialog window before converting and applying the text. This will cause the keyboard input to stop. Should this happens, please close and re-open the dialog box.
• Please do not set up the following characters with in text fields in MTX Editor. 
  [ &, <, >, “, ‘, /, $’, Newline(\n), Tab(\t), e.t.c. ] 
  These characters may disappear or change into an unexpected character.
• When the project file created by MTX Editor V1.0x is opened with MTX Editor V1.1x or later, [Play] selected by "SD Song Select & Play" in the “Preset” dialog, is changed to [No Assign]. In this case, please manually change [No Assign] for all necessary Presets to [Play].
• Please do not use the EEE function (*) of network switches in a Dante network. Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts. Therefore we strongly recommend that:
  1. If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
  2. If you use unmanaged switches, make sure to not use network switches that support the EEE function, since EEE operation cannot be disabled in these switches.
  *EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.

This zip file includes the following software

MTX-MRX Editor / Firmware / Wireless DCP / ProVisionaire Touch / Tio1608-D / R Series (Rio/Ri/Ro) Compatibilities (Win)

Please make sure to use the appropriate versions of firmware and software, referring to the following compatibility charts. Using an unsupported combination may result in malfunction.

Compatibility List

MTX Editor V1.2.2

Fixed Bugs

• Solved a problem in which the channel names of odd channels were not displayed when you clicked the "ROUTER" tab when 2WAY was selected in the OUTPUT CHANNEL SETUP of the "MTX Configuration" dialog box.
• Solved a problem in which a Recall Filter was applied to a channel number, the software would apply the filter to the next lower channel when Recall Filter of a preset was set to the direct input channel (from CH17 to CH24) of MTX5-D.

MTX3 Firmware V1.20

New Function

• The choice of available subnet masks has been extended to increase network IP address range compatibility. (*1)

Fixed Bugs

• Fixed a bug which caused unwanted data to be transmitted immediately following device boot up. Because of this fix, an external remote controller must now request the device status by using the [devstatus runmode] command, in order to establish communication. Please refer to the latest MTX/XMV protocol specification document for the required command sequence.
• Solved a problem that caused the compressor of STIN2 to act in a stereo manner when the channel was set to MONOx2 in the “MTX Configuration” dialog box.
• Solved a problem when a log may be incorrectly retrieved in the "Get Log" dialog box of MTX Editor.
• Solved a problem when the IP SETTING of a device was set to PC mode (DIP switch 6 down), with an IP address other than 192.168.0.x , and then the IP SETTING was changed to UNIT ID mode (DIP switch 6 up), the IP address of the device was not set correctly to 192.168.0.(UNIT ID).

MTX5-D Firmware V1.20

New Functions

• Now supports the MY4-AEC card.
• Now supports the DUGAN-MY16 card.
• The choice of available subnet masks has been extended to increase network IP address range compatibility. (*1)
• Now supports the “Identify device function” of Dante Controller.

Fixed Bugs

• Fixed a bug which caused unwanted data to be transmitted immediately following device boot up. Because of this fix, an external remote controller must now request the device status by using the [devstatus runmode] command, in order to establish communication. Please refer to the latest MTX/XMV protocol specification document for the required command sequence.
• Solved a problem when the SRC setting of the MY8-AE96S card was not saved to MTX5-D.
• Solved a problem that caused the compressor of STIN2 to act in a stereo manner when the channel was set to MONOx2 in the “MTX Configuration” dialog box.
• Solved a problem when a log may be incorrectly retrieved in the "Get Log" dialog box of MTX Editor.
• Solved a problem when the IP SETTING of a device was set to PC mode (DIP switch 6 down), with an IP address other than 192.168.0.x , and then the IP SETTING was changed to UNIT ID mode (DIP switch 6 up), the IP address of the device was not set correctly to 192.168.0.(UNIT ID).

XMV Firmware V1.20

New Functions

• The choice of available subnet masks has been extended to increase network IP address range compatibility. (*1)
• Now supports the “Identify device function” of Dante Controller. (Dante models only)
• In addition to the existing -3dBFs input sensitivity setting, a -20dBFs option has been added for YDIF and Dante inputs. If -20dBFS is set from MTX editor, the digital input sensitivity will match that the analog input sensitivity.

Fixed Bugs

• Fixed a bug which caused unwanted data to be transmitted immediately following device boot up. Because of this fix, an external remote controller must now request the device status by using the [devstatus runmode] command, in order to establish communication. Please refer to the latest MTX/XMV protocol specification document for the required command sequence.
• Solved a problem when the Dante input patch of a XMV (Dante Model) was not correctly set if the UNIT ID of the device was changed.
• Solved a problem when the Dante input patch may be incorrect if synchronization was performed from MTX Editor and a XMV (Dante model) in the system was powered OFF, and then power to that XMV was turned ON.
• Solved a problem when the IP SETTING of a device was set to PC mode (DIP switch 6 down), with an IP address other than 192.168.0.x , and then the IP SETTING was changed to UNIT ID mode (DIP switch 6 up), the IP address of the device was not set correctly to 192.168.0.(UNIT ID).

EXi8/EXo8 Firmware V1.20

New Function

• The choice of available subnet masks has been extended to increase network IP address range compatibility. (*1)

Fixed Bugs

• Fixed a bug which caused unwanted data to be transmitted immediately following device boot up. Because of this fix, an external remote controller must now request the device status by using the [devstatus runmode] command, in order to establish communication. Please refer to the latest MTX/XMV protocol specification document for the required command sequence.
• Solved a problem when the IP SETTING of a device was set to PC mode (DIP switch 6 down), with an IP address other than 192.168.0.x , and then the IP SETTING was changed to UNIT ID mode (DIP switch 6 up), the IP address of the device was not set correctly to 192.168.0.(UNIT ID).

(*1) The following subnet masks can be selected.